With pinball making a huge revival throughout the country, Gentle Giant wishes to make sure that these traditional, stunning machines stay damage-free while being transferred. Oh, and we desire individuals moving them to be safe, too.
In the beginning look, pinball machines can appear daunting to move due to the fact that of their size, weight, and fragility. Fortunately, our proficient Giants have a few tricks up their sleeves to guarantee your pinball is moved with ease.
Folding Down the Headbox
Most of modern pinballs (made in the last 20 years or two) have a hinge system which permits the headbox to be folded down. Early pinball machines had their headboxes bolted on, using either 2 or 4 bolts. All Electro-Mechanical pinballs use this system, together with the early Strong State makers.
Later devices have hinges and utilize a locking system to keep the headbox upright. There may also be 2 bolts inside as included safety, in case the latch is broken or inadvertently un-latched.
For Electro-Mechanical pinball makers, you have to remove the headbox rear access panel to access to the bolts and plugs within. Usually this panel has a lock on it to keep it in place, however over time the key might have been lost. Rather often, there is a screw keeping this panel in place.
When within, get rid of the bolts and unplug the large ports that have circuitry decreasing into the machine. You may desire to identify these connectors to put them back in the right spot, however they need to be different sizes, making it challenging to plug back incorrectly.
You can now get rid of the headbox entirely, or fold the headbox down onto the playfield glass. Make sure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will assist keep the back glass in location.
Early Strong State Pinballs
For early Solid State Pinballs, you will have to eliminate the back glass. There is a lock situated on the headbox in among 3 locations: the left-hand side at the top, right-hand side on top or on top of the headbox in the center.
When opened, get rid of the back glass by raising it up using the lift channel (at the bottom of the glass), and then pull it out from the bottom.
Open up the back box lamp panel by raising the lock situated on either the left-hand side or right-hand side. The panel can now swing out to you, and give you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs require you to raise the light panel in order to swing it open.
Now that you are inside, you can eliminate the bolts, and any plugs that have wires decreasing into the maker. You may want to label these plugs to put them back in the best area. You might not require to get rid of the plugs, as the wiring should be long enough to enable the headbox to be folded down.
At this point, you can secure the light panel and change the back glass.
Modern Strong State Pinballs
For Data East, Sega, and Stern Modern pinballs, there is a turnable lock system located at the back of the headbox. Using the supplied secret, turn the lock 90 ° counter-clockwise.
For Williams, Bally, and Gottlieb, you can quickly unlatch the back box at the back of the maker. This is a simple setup and requires no tools.
If you can now fold down the head box onto the cabinet, you're done. Ensure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.
If you can not fold the head box down, then you require to enter. There is a lock located at the top of the back glass in the. Use the supplied secret to unlock, and eliminate the back glass by raising it up from the bottom, then pulling it out from the bottom.
Next, you will have to get rid of the display panel. You can do this by lifting it up and out. And finally, open the lamp panel. There will be a latch located on either the right-hand or left-hand side. (Some newer Williams and Bally pinballs do not have a separate amp panel, it belongs to the back glass panel. And later Sega and Stern pinballs utilize a fluorescent tube for the back glass lighting).
Get rid of the 2 bolts, put the back box back together, and fold down the head box onto the cabinet. Make certain you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.
Getting rid of the Legs.
Pinball Maker legs are kept in location by 8 bolts. They will be either 5/8 inch or 9/16 inch heads. The modern-day pinballs have captive nuts or threaded plates inside for the bolts to screw into. These bolts can be gotten rid of, and the legs will come off.
However these threaded plates and captive nuts can be harmed, and the usage of additional nuts might have been needed. If this is the case, you will have to open up the front door of the pinball, slide out the playfield glass, and raise the playfield.
With the front door (coin door) open, move the lock down bar latch across and remove the lock down bar. Then slide out the playfield glass, and put in a safe place. Next, raise up the playfield by positioning your hand where the ball drains pipes, and raise the playfield up.
You need to now have access to any nuts that might have been utilized. When any nuts have actually been eliminated, replace the playfield glass and lock down bar, and lock the front door.
Make sure to mark or remember which legs are for the front and back, as they will be adjusted differently to suit.
Loading the Pinball.
You are now ready to transport your pinball machine. Prior to you fill it, make certain you get rid of the pinballs so they do not bounce around throughout transportation.
If you click to read more are moving the pinball using a van or SUV, it may be much easier to get rid of the legs simply prior to packing the device. Grab a friend to help and have one of you supporting the pinball, while the other gets rid of the front legs.
Make certain you strap the pinball in, as you do not desire it moving if you have to stop suddenly!
For Electro-Mechanical pinball machines, you need to get rid of the headbox rear gain access to panel to acquire access to the bolts and plugs inside. (Some newer Williams and Bally pinballs do not have a separate amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs utilize a fluorescent tube for the back glass lighting).
If you are moving the pinball utilizing a van or SUV, it may be easier to remove the legs simply prior to filling the device. Grab a buddy to have and click here now assist one of you supporting the pinball, while the other gets rid of the front legs.